Clutch master cylinder
Clutch master cylinder refers to the hydraulic cylinder operated by the clutch pedal in manual-transmission Pontiac Fiero models.
The clutch master cylinder is part of the Clutch hydraulic system. It converts clutch pedal movement into hydraulic pressure, which is sent through the clutch hydraulic line to the Clutch slave cylinder at the transmission.
Overview
Manual-transmission Fieros use a hydraulic clutch system rather than a mechanical clutch cable.
When the driver presses the clutch pedal, the clutch master cylinder pushes fluid through the hydraulic line. That hydraulic pressure moves the slave cylinder, which operates the clutch release arm.
If the clutch master cylinder does not move enough fluid, the clutch may not fully disengage. This can cause hard shifting, grinding, or difficulty selecting gears.
Related topics:
Location
Image wanted: Photo showing the clutch master cylinder location in a Pontiac Fiero, preferably with the reservoir, hydraulic line, and clutch pedal pushrod area visible.
The clutch master cylinder is located at the front of the car, near the clutch pedal area.
It is mounted to the front bulkhead/firewall area and is connected mechanically to the clutch pedal by a pushrod. Its hydraulic outlet connects to the clutch line running toward the rear of the car.
The clutch slave cylinder is located at the transmission, not at the pedal.
Function
The clutch master cylinder creates hydraulic pressure when the clutch pedal is pressed.
Basic operation:
- The driver presses the clutch pedal.
- The pedal moves the master cylinder pushrod.
- The master cylinder piston moves inside the bore.
- Hydraulic fluid is pushed into the clutch line.
- Fluid pressure moves the slave cylinder at the transmission.
- The slave cylinder moves the clutch release arm.
- The clutch releases.
When the clutch pedal is released, the hydraulic system returns to its resting position.
Relationship to the slave cylinder
The master cylinder and slave cylinder work together.
The master cylinder creates pressure and fluid movement. The slave cylinder converts that hydraulic movement back into mechanical movement at the transmission.
A weak master cylinder can cause the same symptoms as a weak slave cylinder, air in the system, or poor bleeding.
Related topic:
Hydraulic fluid
The clutch master cylinder uses brake fluid as part of the clutch hydraulic system.
Fluid level and condition are important. Low fluid can introduce air into the system. Contaminated or incorrect fluid can damage seals and cause hydraulic problems.
Related topics:
Common problems
Common clutch master cylinder problems include:
- External fluid leak
- Internal seal bypass
- Worn bore
- Low fluid level
- Contaminated fluid
- Air entering the system
- Pushrod or pedal connection problems
- Incorrect replacement part
- Poor bleeding after replacement
A failing master cylinder may not always leak externally. Internal bypass can reduce hydraulic pressure without leaving an obvious puddle.
Symptoms
Possible symptoms of clutch master cylinder problems include:
- Clutch pedal feels soft or spongy
- Clutch pedal slowly sinks
- Clutch pedal does not return normally
- Clutch engages very close to the floor
- Hard shifting
- Grinding when selecting gears
- Difficulty selecting first gear
- Difficulty selecting reverse
- Car creeps forward with clutch pedal pressed
- Fluid level drops over time
- Fluid leak near the pedal area or front compartment
- Problem improves temporarily after bleeding, then returns
These symptoms can also be caused by the slave cylinder, air in the line, clutch pedal problems, or mechanical clutch problems.
External leaks
An external master cylinder leak may show fluid near the master cylinder, reservoir, hydraulic line fitting, or inside the car near the clutch pedal area.
Brake fluid can damage paint, so leaks should be cleaned carefully and repaired promptly.
If the fluid level drops repeatedly, the system should be inspected for leaks at both the master cylinder and slave cylinder.
Internal bypass
A clutch master cylinder can fail internally.
Internal bypass occurs when fluid leaks past the internal piston seal rather than being pushed through the hydraulic line. This can reduce slave-cylinder travel without an obvious external leak.
Possible signs of internal bypass include:
- Soft or inconsistent pedal
- Pedal slowly sinks under pressure
- Insufficient slave-cylinder travel
- Shifting improves after pumping the pedal
- No obvious external leak
Internal bypass can be difficult to diagnose because the system may appear dry from the outside.
Pedal relationship
The clutch master cylinder depends on proper clutch pedal movement.
A bent or worn clutch pedal, worn pedal pivot, incorrect pushrod connection, or damaged pedal hardware can reduce master cylinder travel.
If the master cylinder does not receive full pedal travel, the slave cylinder may not move far enough even if the hydraulic parts are good.
Related topic:
Diagnosis
Basic diagnostic checks include:
- Check clutch fluid level.
- Inspect fluid condition.
- Inspect the master cylinder for external leaks.
- Inspect inside the car near the clutch pedal for fluid leakage.
- Inspect the pushrod and pedal connection.
- Check clutch pedal travel.
- Inspect the hydraulic line fitting at the master cylinder.
- Check for air in the clutch hydraulic system.
- Measure slave-cylinder movement.
- Determine whether the master cylinder may be bypassing internally.
A clutch master cylinder diagnosis should include the rest of the clutch hydraulic system. Replacing only one part may not fix the problem if there is also air in the system, a weak slave cylinder, or a pedal travel issue.
Replacement
Replacing the clutch master cylinder usually requires disconnecting the hydraulic line, disconnecting the pedal pushrod, removing the mounting fasteners, installing the new cylinder, and bleeding the clutch hydraulic system.
General replacement considerations:
- Protect painted surfaces from brake fluid.
- Match the replacement part to the correct model year and transmission setup.
- Inspect the pedal and pushrod connection.
- Avoid introducing dirt into the hydraulic system.
- Bleed the system thoroughly after installation.
- Recheck for leaks after repair.
Related topic:
Bleeding after replacement
After replacing the clutch master cylinder, the hydraulic system must be bled.
Air trapped in the master cylinder, line, or slave cylinder can prevent full clutch release.
If the system is difficult to bleed, check for:
- Air trapped in the line
- Loose fittings
- Weak slave cylinder
- Incorrect bleeding procedure
- Master cylinder not fully primed
- Pedal or pushrod travel problems
- Damaged hydraulic line
Related topic:
Relationship to shifting problems
A weak clutch master cylinder can cause shifting complaints that feel like transmission problems.
Common complaints include:
- “It shifts fine with the engine off, but not with the engine running.”
- “It grinds going into reverse.”
- “It is hard to get into first gear.”
- “The clutch pedal feels soft.”
- “Bleeding helped, but the problem came back.”
These symptoms should be diagnosed through the clutch hydraulic system before assuming the transmission itself is damaged.
Related topics:
Relationship to transmission type
The clutch master cylinder is used on manual-transmission Fieros.
Factory manual transmissions include:
The master cylinder is part of the car's clutch hydraulic system, but replacement parts and related hardware should still be matched to the model year and configuration.
Service notes
When working on the clutch master cylinder:
- Use the correct fluid.
- Protect paint from brake fluid.
- Inspect the clutch pedal and pushrod connection.
- Check for leaks inside and outside the car.
- Bleed the system after replacement.
- Verify slave-cylinder travel after bleeding.
- Do not assume a new master cylinder automatically fixes all clutch-release problems.
- Inspect the slave cylinder if symptoms remain.
- Check the hydraulic line if the system repeatedly loses fluid or draws air.
Notes
A clutch master cylinder can fail without obvious external leakage.
When diagnosing Fiero clutch problems, the master cylinder, slave cylinder, hydraulic line, clutch pedal, bleeding procedure, and clutch assembly should be considered together.