2.8L V6

2.8L V6 refers to the factory V6 engine used in the Pontiac Fiero from 1985 through 1988.

The Fiero 2.8L V6 was part of GM's 60-degree V6 engine family. It was not a Fiero-only engine, but the Fiero version was adapted for the car's transverse mid-engine layout and used multi-port fuel injection.

Overview

The 2.8L V6 was introduced in the Fiero for the 1985 model year. It gave the Fiero a factory performance engine option and was used in sportier models such as the GT, SE, and later the Formula.

Compared with the 2.5L four-cylinder Iron Duke, the 2.8L V6 offered more power, a different exhaust note, and a more performance-oriented character.

The V6 became closely associated with the Fiero GT and remains one of the most recognizable factory Fiero engine configurations.

Location

Image wanted: Photo or diagram showing the 2.8L V6 installed in a Fiero engine bay. Useful images would include the upper intake plenum, distributor, ignition coil, fuel rail, exhaust manifolds, and accessory layout.

The 2.8L V6 is mounted transversely behind the passenger compartment in the Fiero engine bay.

Because of the Fiero's mid-engine layout, some service access differs from front-engine GM cars using related versions of the same engine family.

Fiero applications

The 2.8L V6 was used in several Fiero models from 1985 through 1988.

Common V6-equipped Fieros include:

• 1985 Pontiac Fiero GT
• 1986 Pontiac Fiero GT and SE
• 1986.5 Fiero GT
• 1987 Pontiac Fiero GT and SE
• 1988 Pontiac Fiero GT
• 1988 Pontiac Fiero Formula

Availability varied by model year, trim level, and equipment.

Specifications

Specification	2.8L V6
Engine family	GM 60-degree V6
Displacement	2.8 liters
Configuration	60-degree V6
Fuel system	Multi-port fuel injection
Factory horsepower	Commonly listed as 140 hp
Factory torque	Commonly listed as 160 lb-ft
Valvetrain	Overhead valve / pushrod
Ignition	Distributor-based ignition with ECM-controlled electronic spark timing
Firing order	1-2-3-4-5-6
Fiero model years	1985-1988
Common Fiero applications	GT, SE, Formula, and other V6-equipped models depending on year

Engine family

The Fiero 2.8L V6 belongs to GM's 60-degree V6 engine family.

This is important because some internal engine parts, service concepts, and related engine knowledge overlap with other GM 60-degree V6 applications. However, the Fiero installation has its own intake, exhaust, accessory, cooling, wiring, and packaging details.

Related topic:

• GM 60-degree V6

Fuel injection

The Fiero 2.8L V6 uses multi-port fuel injection.

Each cylinder has its own fuel injector, and fuel delivery is controlled by the ECM based on sensor inputs such as throttle position, manifold pressure, coolant temperature, oxygen sensor feedback, and engine rpm.

Related topics:

• Fuel system
• Fuel injectors
• Fuel pressure test
• ECM
• Oxygen sensor
• Manifold absolute pressure sensor
• Throttle position sensor
• Coolant temperature sensor

Ignition system

The Fiero 2.8L V6 uses a distributor-based ignition system.

Important ignition-related components include:

• Distributor
• Ignition module
• Pickup coil
• Ignition coil
• Spark plug wires
• Spark plugs
• ECM-controlled electronic spark timing

The ignition module is a known failure point on many Fieros, especially when heat, age, poor thermal compound, weak grounds, or poor connectors are involved.

Related topics:

• Ignition module failure
• Ignition timing
• Electronic spark timing
• Code 42
• No-start diagnosis

Firing order

The Fiero 2.8L V6 firing order is:

1-2-3-4-5-6

Cylinder layout, distributor rotation, and firing order for the Fiero 2.8L V6.

Correct spark plug wire routing is important. Incorrect wire order can cause a no-start condition, rough running, backfiring, misfire, poor acceleration, or other ignition-related symptoms.

The diagram shows the cylinder layout, distributor rotation, and number 1 distributor terminal position.

Intake system

The 2.8L V6 uses a distinctive multi-piece intake system.

Major intake-related parts include:

• Upper intake plenum
• Middle intake manifold
• Lower intake manifold
• Throttle body
• Vacuum lines
• EGR tube connection
• MAP sensor vacuum connection

Vacuum leaks in the intake system can cause high idle, lean running, hesitation, poor drivability, and diagnostic trouble codes.

Related topics:

• V6 intake manifold
• Throttle body
• Vacuum leaks
• EGR tube
• Idle problems

Exhaust system

The V6 exhaust system includes exhaust manifolds, crossover/Y-pipe sections, EGR connection, catalytic converter, muffler, and tailpipe system.

Cracked exhaust manifolds, exhaust leaks, broken bolts, and EGR tube issues are common Fiero V6 topics.

An exhaust leak near the oxygen sensor can affect fuel-control diagnosis and may contribute to lean or rich indications.

Related topics:

• V6 exhaust manifolds
• Exhaust leaks
• Oxygen sensor
• Code 44
• Code 45

Cooling system relationship

The 2.8L V6 is part of the Fiero's rear-engine/front-radiator cooling system.

Cooling-system diagnosis on the V6 should consider the complete Fiero cooling system, including:

• Thermostat housing
• Thermostat
• Water pump
• Coolant pipes
• Front Radiator
• Radiator fan
• Proper filling and burping procedure

Related topics:

• Cooling system
• Overheating
• Coolant filling procedure
• Coolant temperature sensor
• Temperature gauge

Common problems

Common 2.8L V6 topics include:

• Ignition module failure
• Vacuum leaks
• EGR tube cracks
• Exhaust manifold leaks
• High idle
• Hard starting
• Fuel pressure problems
• Distributor and pickup coil problems
• Oil leaks
• Cooling-system issues
• Sensor and wiring problems
• Ground problems
• Previous-owner modifications or repairs

Symptoms and diagnosis

Common V6 drivability symptoms may include:

• No-start condition
• Hard starting
• Stalling
• Rough idle
• High idle
• Hesitation
• Poor acceleration
• Misfire
• Poor fuel economy
• Check engine light
• Overheating

Useful starting points include:

• No-start diagnosis
• Diagnostic trouble codes
• ALDL diagnostics
• Fuel pressure test
• Vacuum leaks
• Ignition module failure
• Idle problems
• Ground problems

ALDL diagnostics

The Fiero V6 ECM can output trouble codes and live diagnostic data through the ALDL connector.

Trouble codes can help guide diagnosis, but they should not be treated as automatic proof that a specific part has failed.

Live data can be useful for checking sensor values such as coolant temperature, throttle position, MAP readings, oxygen sensor activity, idle behavior, and fuel-control information.

Relationship to engine swaps

The 2.8L V6 was the factory Fiero performance engine, but many owners later replaced it with larger or newer engines.

Common swap choices include:

• 3.4L V6 swap
• 3800 swap
• 4.9 Cadillac swap
• Northstar swap
• LS4 swap
• Ecotec swap

Some swaps are chosen because they fit the Fiero layout relatively well, while others require more extensive fabrication, wiring, exhaust, cooling, or drivetrain work.

Service notes

When working on the 2.8L V6, keep in mind:

• The Fiero installation has limited access in some areas.
• Heat can affect ignition components, wiring, connectors, and vacuum lines.
• Vacuum-line routing is important.
• Grounds should be clean and secure.
• Fuel pressure should be measured rather than guessed.
• Cooling-system filling procedure is important after service.
• Some parts are shared with other GM applications, while others are Fiero-specific.

Notes

The 2.8L V6 should not be treated as a Fiero-only engine, but the Fiero version has important Fiero-specific installation details.

When ordering parts or diagnosing problems, verify the model year, engine, transmission, emissions equipment, and actual installed components.

See also

• Engine
• GM 60-degree V6
• Fuel system
• Fuel pressure test
• Ignition module failure
• Vacuum leaks
• Cooling system
• Overheating
• Diagnostic trouble codes
• ALDL diagnostics
• Engine swaps
• Factory specifications