Cliff: /* Notes */

2026-08-16T08:45:32Z

Notes

← Older revision		Revision as of 08:45, 16 August 2026
Line 120:		Line 120:
	Likewise, [[Code 14]] or [[Code 15]] does not automatically mean the dashboard gauge sender or gauge is faulty.		Likewise, [[Code 14]] or [[Code 15]] does not automatically mean the dashboard gauge sender or gauge is faulty.

	Part number for I4 2.5 gauge sender is 25036628.		Part number for L4 2.5 gauge sender is 25036628.

	Part number for V6 2.8 gauge sender is 25036809.		Part number for V6 2.8 gauge sender is 25036809.

Larry Carguy at 02:01, 14 August 2026

2026-08-14T02:01:24Z

← Older revision		Revision as of 02:01, 14 August 2026
Line 120:		Line 120:
	Likewise, [[Code 14]] or [[Code 15]] does not automatically mean the dashboard gauge sender or gauge is faulty.		Likewise, [[Code 14]] or [[Code 15]] does not automatically mean the dashboard gauge sender or gauge is faulty.

	Part number for I4 2.5 gauge sender is 25036628~~{{1}}~~.		Part number for I4 2.5 gauge sender is 25036628.

	Part number for V6 2.8 gauge sender is 25036809~~{{1}}~~.		Part number for V6 2.8 gauge sender is 25036809.

	== See also ==		== See also ==

Larry Carguy at 01:49, 14 August 2026

2026-08-14T01:49:55Z

← Older revision		Revision as of 01:49, 14 August 2026
Line 119:		Line 119:

	Likewise, [[Code 14]] or [[Code 15]] does not automatically mean the dashboard gauge sender or gauge is faulty.		Likewise, [[Code 14]] or [[Code 15]] does not automatically mean the dashboard gauge sender or gauge is faulty.

			Part number for I4 2.5 gauge sender is 25036628{{1}}.

			Part number for V6 2.8 gauge sender is 25036809{{1}}.

	== See also ==		== See also ==
Line 137:		Line 141:
	[[Category:Diagnostics]]		[[Category:Diagnostics]]
	[[Category:Cooling system]]		[[Category:Cooling system]]

			== Sources ==
			1. http://www.calgaryfieros.com/OSGdocs/temp-gauge-sender.html, viewed 8/13/2026

Cliff: Created page with "'''Temperature gauge''' refers to the dashboard engine-temperature gauge used in the Pontiac Fiero Instrument cluster. The temperature gauge displays engine coolant temperature to the driver. It should not be confused with the Coolant temperature sensor used by the ECM. == Overview == The Fiero uses separate temperature-related parts for different purposes. The dashboard temperature gauge receives its signal from the temperature gauge sender. The ECM..."

2026-07-06T20:38:41Z

Created page with "'''Temperature gauge''' refers to the dashboard engine-temperature gauge used in the Pontiac Fiero Instrument cluster. The temperature gauge displays engine coolant temperature to the driver. It should not be confused with the Coolant temperature sensor used by the ECM. == Overview == The Fiero uses separate temperature-related parts for different purposes. The dashboard temperature gauge receives its signal from the temperature gauge sender. The ECM..."

New page

'''Temperature gauge''' refers to the dashboard engine-temperature gauge used in the [[Pontiac Fiero]] [[Instrument cluster]].

The temperature gauge displays engine coolant temperature to the driver. It should not be confused with the [[Coolant temperature sensor]] used by the [[ECM]].

== Overview ==

The Fiero uses separate temperature-related parts for different purposes.

The dashboard temperature gauge receives its signal from the temperature gauge sender.

The ECM receives coolant temperature information from the ECM coolant temperature sensor.

The radiator fan may be controlled by a separate fan switch or fan-control circuit, depending on year and configuration.

Because these parts are separate, a problem with one does not automatically mean the others are faulty.

== Location ==

{{Image wanted|Photo or diagram showing the Fiero temperature gauge in the instrument cluster and the engine-mounted temperature gauge sender location. Ideally include both the 2.8L V6 and 2.5L four-cylinder sender locations.}}

The temperature gauge is located in the instrument cluster.

The temperature gauge sender is mounted on the engine. Its exact location depends on the engine and year.

On the 2.8L V6, the gauge sender is located separately from the ECM coolant temperature sensor.

On the 2.5L four-cylinder, the sender location may vary by year and engine configuration.

== Gauge sender versus ECM sensor ==

The temperature gauge sender and ECM coolant temperature sensor are separate parts.

The gauge sender is used by:

* Dashboard temperature gauge
* Temperature warning light, depending on circuit and year

The ECM coolant temperature sensor is used by:

* [[ECM]]
* Fuel mixture calculations
* Idle and warm-up behavior
* Closed-loop decisions
* Diagnostic trouble codes such as [[Code 14]] and [[Code 15]]

This distinction is important during diagnosis.

== Common problems ==

Common temperature-gauge-related problems include:

* Gauge reads too high
* Gauge reads too low
* Gauge does not move
* Gauge pegs suddenly
* Gauge behaves erratically
* Temperature warning light problem
* Bad sender
* Wiring fault
* Poor connector contact
* Instrument cluster problem
* Ground problem

== Gauge pegging ==

Some Fieros are known for temperature-gauge needle pegging during start-up due to wiring or circuit behavior. This can damage or misposition the gauge needle over time.

If the gauge needle is stuck, reads incorrectly, or has moved beyond its normal range, the gauge and related wiring should be inspected.

Related topics:

* [[Instrument cluster]]
* [[Electrical system]]
* [[Ground problems]]
* [[Wiring diagrams]]

== Overheating diagnosis ==

A high temperature-gauge reading may indicate an actual overheating problem, but the gauge circuit should not be the only source of diagnosis.

If overheating is suspected, check the cooling system directly.

Related topics:

* [[Overheating]]
* [[Cooling system]]
* [[Coolant filling procedure]]
* [[Radiator fan]]
* [[Thermostat]]
* [[Water pump]]

== ECM data comparison ==

Live ECM data through [[ALDL diagnostics]] can help compare the ECM coolant temperature reading with the dashboard gauge.

If the ECM temperature reading appears normal but the dashboard gauge reads incorrectly, the problem may be in the gauge sender, gauge wiring, instrument cluster, or gauge itself.

If both the ECM data and dashboard gauge indicate overheating, the cooling system should be checked.

== Diagnosis ==

Basic diagnostic checks include:

# Determine whether the engine is actually overheating.
# Check coolant level and cooling-system condition.
# Inspect the temperature gauge sender connector.
# Inspect gauge-sender wiring.
# Check instrument cluster operation.
# Check grounds and connectors.
# Compare ECM coolant temperature through [[ALDL diagnostics]] if live data is available.
# Check the cooling system if actual overheating is suspected.
# Check the gauge sender and gauge circuit if the engine temperature is normal but the gauge reads incorrectly.

== Notes ==

Do not confuse the temperature gauge sender with the ECM coolant temperature sensor.

A dashboard gauge problem does not automatically mean the ECM is receiving incorrect coolant temperature data.

Likewise, [[Code 14]] or [[Code 15]] does not automatically mean the dashboard gauge sender or gauge is faulty.

== See also ==

* [[Instrument cluster]]
* [[Coolant temperature sender]]
* [[Coolant temperature sensor]]
* [[Cooling system]]
* [[Overheating]]
* [[Coolant filling procedure]]
* [[ALDL diagnostics]]
* [[Code 14]]
* [[Code 15]]

[[Category:Fieropedia]]
[[Category:Electrical system]]
[[Category:Interior]]
[[Category:Diagnostics]]
[[Category:Cooling system]]

Temperature gauge - Revision history

Cliff: /* Notes */

Larry Carguy at 02:01, 14 August 2026

Larry Carguy at 01:49, 14 August 2026