Cliff: Created page with "'''Manifold absolute pressure sensor''' refers to the manifold-pressure sensor used by the Pontiac Fiero ECM. The manifold absolute pressure sensor tells the ECM how much pressure or vacuum is present in the intake manifold. The ECM uses this information to estimate engine load and to calculate fuel delivery, ignition timing, and drivability behavior. == Overview == The manifold absolute pressure sensor is often abbreviated as MAP sensor. The MAP sensor is on..."

2026-07-06T20:30:13Z

Created page with "'''Manifold absolute pressure sensor''' refers to the manifold-pressure sensor used by the Pontiac Fiero ECM. The manifold absolute pressure sensor tells the ECM how much pressure or vacuum is present in the intake manifold. The ECM uses this information to estimate engine load and to calculate fuel delivery, ignition timing, and drivability behavior. == Overview == The manifold absolute pressure sensor is often abbreviated as MAP sensor. The MAP sensor is on..."

New page

'''Manifold absolute pressure sensor''' refers to the manifold-pressure sensor used by the [[Pontiac Fiero]] [[ECM]].

The manifold absolute pressure sensor tells the ECM how much pressure or vacuum is present in the intake manifold. The ECM uses this information to estimate engine load and to calculate fuel delivery, ignition timing, and drivability behavior.

== Overview ==

The manifold absolute pressure sensor is often abbreviated as MAP sensor.

The MAP sensor is one of the main engine-load sensors used by the Fiero ECM. When intake manifold vacuum changes, the MAP sensor signal changes. The ECM uses this signal together with other inputs such as throttle position, coolant temperature, air temperature, oxygen sensor activity, and engine rpm.

A faulty MAP sensor, poor vacuum connection, damaged hose, wiring problem, or connector problem can cause major drivability issues.

== Location ==

{{Image wanted|Photo or diagram showing the manifold absolute pressure sensor location. Ideally include both the 2.8L V6 and 2.5L four-cylinder locations if different.}}

The MAP sensor is mounted in the engine compartment and connected to intake manifold vacuum.

On the 2.8L V6, the MAP sensor is located near the upper intake / throttle body area and is connected to manifold vacuum by a short vacuum hose.

On the 2.5L four-cylinder, the MAP sensor is also located where it can receive an intake manifold vacuum signal, though the exact mounting location and appearance may vary by year and engine configuration.

The MAP sensor should not be confused with the [[Manifold air temperature sensor]]. The MAP sensor measures manifold pressure, while the MAT sensor measures incoming air temperature.

== Sensor operation ==

The MAP sensor converts intake manifold pressure into an electrical signal for the ECM.

In general:

* High vacuum / low manifold pressure produces a lower load reading.
* Low vacuum / high manifold pressure produces a higher load reading.
* Opening the throttle usually lowers vacuum and increases the MAP reading.
* Closing the throttle usually increases vacuum and lowers the MAP reading.

The ECM uses this information to help determine how much air the engine is taking in.

== Related trouble codes ==

MAP-sensor-related diagnostic trouble codes include:

* [[Code 33]] - MAP sensor circuit, high voltage or unusually low vacuum / high pressure indication
* [[Code 34]] - MAP sensor circuit, low voltage or unusually high vacuum / low pressure indication

== Code 33 ==

[[Code 33]] indicates that the ECM is seeing a MAP sensor signal that represents unusually low vacuum or high manifold pressure.

Possible causes include:

* Disconnected MAP sensor vacuum hose
* Leaking MAP sensor vacuum hose
* Faulty MAP sensor
* MAP sensor wiring problem
* Poor connector contact
* Vacuum leak
* Engine running poorly enough to create low vacuum
* ECM input problem

== Code 34 ==

[[Code 34]] indicates that the ECM is seeing a MAP sensor signal that represents unusually high vacuum or low manifold pressure.

Possible causes include:

* Faulty MAP sensor
* MAP sensor wiring problem
* Poor connector contact
* Open or shorted MAP sensor circuit
* Blocked MAP sensor vacuum hose
* Incorrect MAP sensor vacuum signal
* ECM input problem

== Symptoms ==

Possible symptoms of a MAP sensor or MAP circuit problem include:

* Check engine light
* Hard starting
* Rough idle
* Hesitation
* Stalling
* Poor acceleration
* Poor fuel economy
* Rich running
* Lean running
* Black exhaust smoke
* Poor drivability

== Diagnosis ==

Basic diagnostic checks include:

# Check for stored diagnostic trouble codes.
# Inspect the MAP sensor vacuum hose.
# Check for a disconnected, cracked, leaking, blocked, or incorrectly routed vacuum hose.
# Inspect the MAP sensor connector.
# Inspect MAP sensor wiring for damage.
# Check for corrosion or poor contact at the connector.
# Check for vacuum leaks.
# Check for other stored trouble codes.
# Compare MAP data through [[ALDL diagnostics]] if live data is available.
# Check ECM connector condition if the sensor, vacuum hose, and wiring appear correct.

== Vacuum hose ==

The MAP sensor depends on an accurate manifold vacuum signal. A bad vacuum hose can make a good MAP sensor report incorrect information to the ECM.

Common hose problems include:

* Cracked rubber hose
* Disconnected hose
* Loose hose ends
* Collapsed hose
* Blocked hose
* Incorrect hose routing

Related topics:

* [[Vacuum leaks]]
* [[Vacuum lines]]
* [[Intake manifold]]

== ALDL data ==

Live ECM data through [[ALDL diagnostics]] can be useful when diagnosing MAP sensor problems.

If the MAP value is obviously wrong for the engine condition, the vacuum hose, sensor, wiring, connector, and ECM input should be checked.

MAP readings should be interpreted together with engine rpm, throttle position, coolant temperature, and other sensor data.

== Relationship to fuel mixture ==

The MAP sensor is one of the ECM's most important fuel-calculation inputs.

A wrong MAP signal can cause the ECM to calculate engine load incorrectly, which may result in:

* Too much fuel
* Too little fuel
* Poor throttle response
* Rough running
* Stalling
* Poor fuel economy

Related inputs include:

* [[Throttle position sensor]]
* [[Coolant temperature sensor]]
* [[Manifold air temperature sensor]]
* [[Oxygen sensor]]

== Notes ==

A MAP sensor trouble code does not automatically mean the MAP sensor itself has failed.

Vacuum hose problems, wiring faults, poor connectors, vacuum leaks, engine mechanical problems, and ECM input problems can all cause MAP-related trouble codes.

Always inspect the vacuum connection before replacing the sensor.

== See also ==

* [[Diagnostic trouble codes]]
* [[ALDL diagnostics]]
* [[ECM]]
* [[Vacuum leaks]]
* [[Fuel system]]
* [[Throttle position sensor]]
* [[Manifold air temperature sensor]]
* [[Code 33]]
* [[Code 34]]

[[Category:Fieropedia]]
[[Category:Diagnostics]]
[[Category:Electrical system]]
[[Category:Engine]]
[[Category:Fuel system]]

Manifold absolute pressure sensor - Revision history